Can't Read Qa Sticker on Fender Amp

Dating 1951-1969

On the inside of the cabinets of Fender amplifiers that were built afterwards 1950 and before 1970, a sticker is mostly attached. This indicates the blazon of the tubes used and their location on the chassis. Also on this sticker stamped ii letters (sometimes handwritten) indicating a date code.

From 1990
All Fender amplifiers manufactured from 1990 until at present, have a date code printed on the quality balls (QA) sticker on the rear of the chassis. This black-silver sticker shows signatures or initials of employees after the finished noise and electric tests.
The concluding line also has a stamped or handwritten 2-letter date code. Handwritten is sometimes hard to read (run into image).
The first letter is the year and the second letter is month.


If no QA or tube location sticker is found or it is bad read, look at the rear of the chassis on the correct side where a chassis number is punched. Yous can decipher the year of construction using the date decoder. Date code from 1951 to 1969 and and from 1990

Letter Code	Vintage yr	Retro yr	Month
A	1951	1990	Jan
B	1952	1991	February
C	1953	1992	March
D	1954	1993	April
E	1955	1994	May
F	1956	1995	June
G	1957	1996	July
H	1958	1997	August
I	1959	1998	September
J	1960	1999	October
K	1961	-	November
L	1962	-	December
M	1963	-	-
N	1964	-	-
O	1965	-	-
P	1966	-	-
Q	1967	-	-
R	1968	-	-
S	1969	-	-

Some indications that you can also recognize the production year.
Before the CBS era (before 1965) Blackface amplifiers were feature labeled Fender Electric Instrument .
Blackface amplifiers from 1964 and some from early on 1965 did non take the Fender logo on the grill cloth.

After the acquisition of Fender by CBS in Jan 1965, amplifiers were labeled as Fender Musical Instruments .

From 1974 a potentiometer with pressure-pull switch was added to some amplifiers.

The logo on the grill cloth of the amplifier also gives an indication of when it was produced.
A logo with tail is from before 1973. Afterward 1973 the logo was tailless. With few exceptions. As long as in that location was a stock with tail logos, they were used randomly in 1973.
Amplifiers from that year and perhaps too in 1974 tin therefore have the new or old logo.

tailless (after 1973)      with tail (before 1973) At that place are a number of amplifiers from '68 and '69 appear, including the Vibro Gnaw and Bassman, which as well had a tailless logo. However, these logos are made of plastic and slightly smaller than the metals. Dating of components
If in that location are no sticker or chassis number at all, the the components can also offer a solution for dating the year of structure of the amplifier.
(Bold the components is original and has not been replaced.)

Transformer
With help of the Environmental impact assessment (Electronics Manufacture Clan) number on the transformer, the production engagement tin can be determined.
This is not the production date of the amplifier, because the transformer has already been made before and may have been for a while in storage.

The EIA number on the transformer which Fender has used the nearly starts with 606, followed by 3 or 4 digits. 606 is the manufacturer (Woodward-Schumacher), but a transformer from some other manufacturer may also have been used. (see Eia factory codes)

With iii digits, the offset digit is the last digit of the decade of the 20th century. The last two digits is the week of that year.
At 4 digits, the first two digits are the year of the 20th century.

Instance: 606 6849 is 1968 week 49. If the production date of the transformer is now known, add together at least 6 months to the production date of the amplifier. From the example, the amplifier could have been built in 1969.

Speakers and potentiometers
What applies to the transformer as well applies to speakers and potmeters.

Speakers
Fender used Jensen speakers until 1972.
In that year the Jensen product was transferred to Rola. (Rola was already a part of Jensen). When Rola started making speakers for Jensen in 1972, Rola also used Jensen's EIA code in the get-go (220). At the end of 1972, Rola changed the code to 285.

CTS
Sometimes Fender used CTS speakers in the 1960s. Between the mid 1960s and early 1970s, the CTS 10-inch Alnico was regularly used in Super Reverbs.

Eminence
Eminence (founded in 1966 by former CTS employee Bob Gault) fabricated speakers specially for Fender according to those specifications. From the early on eighties these were standard in most all tube amplifiers.

Utah
Despite the fact that the Utah speakers from the 50s and 60s were of very good quality, Fender did not utilise them much during that period. Information technology was not until the 1970s that these spaekers became more widely used.

But non all speaker manufacturers work with an Eia lawmaking.
For example, Celestion has its own date coding method that consists of ii letters with 1 or 2 digits.
Case: GK12 is July 12, 1977.
23HA is August 23, 1956 or August 23, 1968.
The Celestion dating system is included in the speaker decoder.
Potentiometers
In the 1950s, Fender mainly used potmeters from the Stackpole brand (304). Halfway through 1963, the switch was fabricated to the CTS make (137). In 1967 Fender bought a very large stock of CTS and was used for over 5 years. Amplifiers (and likewise guitars) made in 1973 can therefore still take the 1967 potmeters with Environmental impact assessment numbers from the stock that was purchased in 1967.
(see also Potentiometer decoder) More manufacturers can be found with the EIA factory decoder by searching on their EIA code or in the component list.

Environmental impact assessment manufactory codes and component listing

ruiztutes1978.blogspot.com

Source: https://www.guitarinsite.nl/serienummers-fender-amps_eng.php

Share this post